
Drips that will not stop after a new cartridge. Kitchen faucet that swivels loose at the base. Angle stops seized shut so you cannot isolate the sink. We handle every residential faucet call in Lake Dallas — rebuilds, replacements, and the shutoffs behind them — with parts stocked for Lake Dallas's hard water and the fixtures found in Oak Shores and Shady Shores Border.
Upper Trinity Regional Water District supplies Lake Dallas with 8-10 grain hard water. That mineral load is what eats the ceramic discs inside Delta, Moen, and Kohler cartridges within 5-7 years, why aerators clog every few months, and why the pop-up drain assembly fuses to the tailpiece. A new cartridge is often the fix, but the diagnosis has to come first — a leaking base is a different problem than a leaking spout, and we treat them as such.
Older Lake Dallas homes still have compression-style stem faucets from the 70s and 80s. Parts are still available, but the seats often need to be re-cut, not just re-washered, and the angle stops feeding them are typically the original multi-turn valves — seized shut when you actually need them. We bring quarter-turn replacement stops on every faucet call and swap them at the same visit if yours will not close.
For full replacements we carry pull-down kitchen faucets, widespread and centerset bathroom sets, and freestanding tub fillers from the brands that hold up in Lake Dallas water. If you have already bought the fixture, no problem — we install customer-supplied faucets with the same one-year labor warranty on our work.

A slow drip wastes ~3,000 gallons a year at Lake Dallas water rates. Most of these are one-visit fixes.
Constant drip from the spout means a failed cartridge or a scored seat. On hard-water Lake Dallas homes, both wear together.
Too much play or a handle that fights back is a cartridge or stem issue — not the handle screw. Common on 5-10 year old Moen and Delta.
Low pressure at only the kitchen or one bath usually means a clogged aerator, a partially closed angle stop, or scale buildup in the supply.
A pressure-balance or thermostatic cartridge failing on the hot side. Especially common in tub/shower valves — an easy fix if caught early.
Water pooling at the base, not from the spout, means a failed O-ring on the swivel or a cracked deck plate. Different fix than a spout drip.
A faucet that wobbles at the deck has a failed mounting nut or a rotted-out backer washer. Left alone, it stresses the supply lines under the sink.
Most faucet calls in Lake Dallas are one-visit jobs. We diagnose first, then quote before any wrench turns.
A drip from the spout, a leak from the base, and a stiff handle are three different repairs. We isolate the failure — cartridge, seat, O-ring, or shutoff — before quoting.
Every faucet call includes testing the shutoffs under the sink. If they will not close cleanly, we quote quarter-turn replacements at the same visit so you never lose the ability to isolate the fixture.
Upfront pricing before we start. Cartridge rebuilds, full replacements, and shutoff swaps are line-itemed so you see exactly what each part costs.
Genuine Delta, Moen, Kohler, and Pfister cartridges on the truck. For customer-supplied fixtures, we verify what you have before pulling the old one so you are not left without a working sink.
Run the faucet at full flow hot and cold, check every joint under the sink with a paper towel, clean up the workspace, and walk you through the fix before we go.
Housing age predicts the failure mode.
Waterfront and near-waterfront customs with high-end kitchen fixtures.
Older lake-cabin conversions with original galvanized supply — full angle-stop replacement common.
Pre-1970s homes with original compression stem faucets — seat re-cutting and modernization.
Mid-century stock updated over the years — mixed brand and vintage fixtures.
Established customs with lake-view kitchens — pull-down faucet diverter service.
Newer construction near Hickory Creek border — modern fixtures with light maintenance calls.

We stock genuine cartridges for Delta, Moen, Kohler, Pfister, American Standard, and Grohe on every truck, plus quarter-turn angle stops, braided supply lines, and pop-up drain assemblies. That means most Lake Dallas faucet calls are single-visit — no parts run mid-job, no leaving you with a torn-apart sink overnight.
Every faucet repair carries a one-year labor warranty from Aqua Pure Plumbing, plus the manufacturer's warranty on parts. Master plumber licensed by the Texas State Board of Plumbing Examiners, insured and bonded, dispatching from The Colony — Lake Dallas is 20 minutes north and part of our daily lake-corridor route. Same-day for active drips and seized shutoffs.
Faucet work often uncovers failed angle stops, corroded supply lines, or a slow drain under the sink. We handle all of it in the same visit.

Electronic detection under Lake Dallas slabs — reroute options that save your finished floors when possible.

Trenchless replacement for the aging laterals across Lake Dallas's older runs — camera first, quote in writing, minimal yard damage.

Acoustic, thermal, and pressure testing to pinpoint hidden leaks in Lake Dallas slab and wall lines without tearing into finishes.

Licensed install, repair, and pressure-testing for Lake Dallas homes — every line signed off to Texas code and Atmos requirements.

Full-clear service and camera confirmation for the drains under Lake Dallas's neighborhoods.

Repair, flush, and replacement of tank units — including attic and garage heaters common to Lake Dallas homes.

Install, service, and annual descaling — Lake Dallas's hard tap water eats tankless heat exchangers without it.

Same-day and after-hours response across Lake Dallas for burst pipes, heater failures, and main-line backups.

High-pressure cleaning that clears scale, grease, and roots from Lake Dallas's lateral runs — full-diameter, lasting clean.

Rebuilds, wax-ring resets, flange repairs, and full replacements — the running toilets and rocking bowls in Lake Dallas homes.

Jam clearing, leaking-unit swaps, and quiet 3/4 HP upgrades for Lake Dallas kitchens — same-visit install.
Cartridge rebuild, full replacement, or shutoff swap — parts on the truck, price in writing.